Fleet Maintenance Management: Strategies for Cost Reduction & Operational Efficiency
Discover how fleet maintenance reduces costs and boosts productivity. Learn key tools and strategies to keep your fleet of vehicles in top condition.
Resources
Browse our full library of resources all in one place, including webinars, whitepapers, podcast episodes, and more.
Self-Service & Support
Looking for self‑service training, best practices, helpful videos, product resources, or support? You’re in the right place.
Table of contents
Condition monitoring is the practice of measuring parameters that signal machine health, such as vibration, temperature and lubricant condition. Condition-based maintenance (CBM) is the strategy that uses those measurements to decide when to act, so work happens when the data shows a need rather than on a fixed calendar. In short, condition monitoring supplies the readings, and condition-based maintenance turns them into maintenance decisions.
Picture a plant that collects vibration and temperature readings on its pumps and motors. The data sits in a spreadsheet or a vendor dashboard, and nobody acts on it until an asset fails. The readings were accurate, but no one turned them into a maintenance task, so the warning went unused. This article covers what to measure, which assets to measure it on and how to turn each reading into action.
Condition-based maintenance is a strategy that schedules work when the measured condition of an asset shows a need. Time-based preventive maintenance performs tasks on a fixed calendar or usage interval, whether or not the asset needs attention. Run-to-failure waits for the asset to break before any work happens. Condition-based maintenance sits between the two: It acts early enough to avoid a breakdown, but only when the data supports it.
The idea rests on the potential failure to functional failure (P-F) interval. As reliability guidance on the P-F curve explains, potential failure (P) is the earliest point at which a developing problem becomes detectable, and functional failure (F) is the point at which an asset can no longer perform its intended function. The time between the two is the window to plan and act. Each technique buys a different amount of warning in that window, and a technique that detects a problem earlier gives a team more time to plan the repair.
The two terms describe different stages of the same journey. Condition monitoring supplies the data. Condition-based maintenance acts when a reading crosses a set limit. Predictive maintenance goes a step further and uses trend data and models to estimate when a failure will occur. Many programs move from preventive maintenance to condition-based maintenance to predictive maintenance over time, adding data and analysis at each stage.
The stages differ in what they ask of a team, because each one needs more data and analysis than the one before. For a full comparison of the strategies, read our guide to preventive vs. predictive maintenance. To see how a computerized maintenance management system (CMMS) supports the later stages, explore our predictive maintenance software.
Each technique catches different faults on different assets, so the right choice depends on how an asset fails.
Vibration analysis measures how a machine moves, usually with an accelerometer mounted on the housing. It detects imbalance, misalignment, looseness and bearing defects in rotating equipment such as motors, pumps and gearboxes.
Infrared thermography uses a thermal camera to find abnormal heat in electrical connections, motors, bearings and couplings. Technicians usually check these assets with a handheld camera on an inspection route, so a thermography program can start without installed sensors.
Oil analysis tests a lubricant sample for wear metals, contamination, water and viscosity changes. Gearboxes, hydraulic systems and engines are the strongest use cases, because the oil carries evidence of wear inside components that technicians cannot inspect while the machine runs.
Ultrasonic monitoring listens for high-frequency sound that the human ear cannot hear. It picks up early bearing wear, lubrication problems, electrical arcing, and compressed air and gas leaks.
Motor current signature analysis (MCSA) measures the current an induction motor draws. A clamp-on sensor, usually placed at the motor control center, captures that current while the motor runs under normal load. Patterns in the current spectrum can reveal broken rotor bars, air gap eccentricity and some bearing and load-side faults. Peer-reviewed research on broken rotor bar detection describes MCSA as a widely used noninvasive method.
Because the readings come from the control center rather than the machine, MCSA reaches motors that are difficult or unsafe to access, and the motor keeps running during the test. It is separate from a motor circuit analysis, which is a different test that is usually performed with the motor de-energized. MCSA is most sensitive to rotor and electrical faults, so many teams pair it with vibration analysis to cover bearings and mechanical faults.
The table below pairs five common assets with the readings that suit them.
| Asset | What to measure | What it catches |
| Electric motors | Motor current, vibration and temperature | Broken rotor bars, air gap eccentricity, bearing defects, imbalance and overheating connections |
| Centrifugal pumps | Vibration, ultrasonic readings and bearing temperature | Misalignment, imbalance, bearing wear and lubrication problems |
| Gearboxes | Oil analysis and vibration | Wear metals, contamination, water, viscosity changes and bearing defects |
| Compressors | Vibration, oil analysis and ultrasonic readings | Bearing defects, worn or contaminated lubricant and compressed air or gas leaks |
| Conveyors | Thermography and vibration on drive motors, gearboxes and couplings | Abnormal heat, misalignment and bearing defects |
Start by ranking assets by criticality and focusing on the failure modes that would stop production. A condition monitoring program works best when technique selection follows those priorities rather than sensor availability. Reliability guidance notes that lower-priority assets may suit simpler time-based methods or run-to-failure, and low-cost, noncritical assets often fit that description.
A reading that nobody acts on has no value. These five steps turn data into action:
The last step matters as much as the first. Each completed job shows whether a limit was too tight or too loose, and the next reading starts from a better baseline. A system built around work order management keeps that history in one place, so every inspection builds on the last. To see how that handoff can work in practice, book a demo.
Accruent Maintenance Connection is a CMMS and enterprise asset management (EAM) solution where condition alerts become scheduled, assigned and documented work. It does not replace sensors or analytics tools. Condition monitoring partners detect changes in asset health, and Maintenance Connection centralizes asset information and turns those insights into maintenance work. Our condition-based monitoring video shows how that workflow fits together.
Maintenance Connection supports each step of the loop:
For field execution, Accruent Field gives technicians the assigned work, asset history and information they need to act.
Choosing what to measure matters, but the real value comes from acting on the reading before the asset fails. Match each technique to the assets and failure modes that carry the most risk, set limits that trigger work and make sure every alert reaches a team that can act on it. To see how Accruent Maintenance Connection turns condition data into scheduled, assigned and documented work, book a demo of Accruent Maintenance Connection.
The benefits of condition-based maintenance include reduced unplanned downtime, lower repair costs and extended asset life. Condition-based maintenance delivers these benefits by finding problems while they are still small. A fourth benefit is fewer unnecessary preventive tasks. Time-based schedules do not account for asset wear, so they can trigger work on healthy equipment, while condition data directs effort to the assets that show a need.
For an example of condition-based maintenance, consider this scenario: A gearbox oil sample shows rising levels of wear metals. The reading crosses its alert limit, and a planner schedules an inspection for the next planned stop instead of waiting for an emergency repair. The team replaces the worn component before the situation is critical.
The International Organization for Standardization (ISO) publishes ISO 17359:2018, the general guideline for setting up a condition monitoring program for machines. It applies to all machines and includes references to associated standards that support the process. ISO reviewed and confirmed the standard in 2023, so this edition remains current.
Discover how fleet maintenance reduces costs and boosts productivity. Learn key tools and strategies to keep your fleet of vehicles in top condition.
Discover the meaning and secrets to successful maintenance management. Explore strategies to cut maintenance costs and boost operational efficiency.
Learn how construction equipment maintenance software and CMMS tools reduce downtime, cut costs & extend equipment life. Explore key features and ...
Subscribe to stay up to date with our latest news, resources and best practices.
* To unsubscribe at any time, please use the “Unsubscribe” link included in the footer of our emails.